Specifications: Weighted, hermetically sealed, amber glass capsules; 1/4″ (6.4 mm) OD, 3/4″ (19 mm) long, slightly longer for higher densities; permanently marked for identification; precisely calibrated at 23°C (73.4°F) unless otherwise specified.

Application: Sink-Floats are usually selected to meet specific density liquid monitoring or individual liquid density requirements by ordering singly, in pairs, or in series by Catalog No.

(M)SDS
Data Sheet

Purchase orders must specify the exact density and tolerance. If this information is omitted, the widest tolerance will be supplied.

(M)SDS
Data Sheet

Purchase orders must specify the exact density and tolerance. If this information is omitted, the widest tolerance will be supplied.

(M)SDS
Data Sheet

Purchase orders must specify the exact density and tolerance. If this information is omitted, the widest tolerance will be supplied.

(M)SDS
Data Sheet

Purchase orders must specify the exact density and tolerance. If this information is omitted, the widest tolerance will be supplied.

(M)SDS
Data Sheet

Purchase orders must specify the exact density and tolerance. If this information is omitted, the widest tolerance will be supplied.

(M)SDS
Data Sheet

Purchase orders must specify the exact density and tolerance. If this information is omitted, the widest tolerance will be supplied.

(M)SDS
Data Sheet

Purchase orders must specify the exact density and tolerance. If this information is omitted, the widest tolerance will be supplied.

(M)SDS
Data Sheet

Purchase orders must specify the exact density and tolerance. If this information is omitted, the widest tolerance will be supplied.

Application: Sink-Float Screening Sets are available in series commonly used in making quick estimates of densities.

The precise density of a Sink Float Standard within a set may not end in a “0” or a “5”. However, its precise density will be clearly marked and calibrated within the chosen tolerance (i.e. A nominal 1.00 gm/cc Standard for Set #13550 will be marked with its density within its tolerance so its density will be a number between .995 and 1.005 and marked as to its actual density).

Standard Temperature: Calibration will be at 23°C unless another temperature is specified. See below.

Temperature Adjustment Charge: For other than 23°C Use CAT # 13200; $158.75 (For each combination density-temperature specification in a single order)

Inorganic Salts can be supplied in any density requested from 1.00 to 2.49 gm/cc. When ordering, please specify catalog number, specific density of liquid, and tolerance required. Keep in mind that a single liquid can have only one density.

NOTE: All the Inorganic Salts are slightly acid, relatively nontoxic, and water soluble

(M)SDS

(M)SDS

(M)SDS

(M)SDS

(M)SDS

(M)SDS

(M)SDS

Heavy Liquids in the Organic Series can be supplied in any density requested from 0.80 to 3.31 gm/cc. When ordering, please specify catalog number, specific density of liquid, and tolerance required. Keep in mind that a single liquid can have only one density.

NOTE: Formulated from organic liquids. Low end member is stable and nontoxic, high end members are halogenated organic compounds. Miscible with most organic solvents.

CAUTION: Take normal precautions against contact and inhalation of halogenated organics.

(M)SDS 0.80 -0.83

(M)SDS 0.84 – 1.00

(M)SDS 1.01 – 2.95

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 1.01 – 2.95

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 1.01 – 2.95

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 1.01 – 2.95

(M)SDS 2.96 – 3.31

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 2.96 – 3.31

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 2.96 – 3.31

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 2.96 – 3.31

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 2.96 – 3.31

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 2.96 – 3.31

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

(M)SDS 2.96 – 3.31

When ordering, please specify catalog number, specific density of liquid, and tolerance required.

About 30 ml of Organic Series Heavy Liquids, supplied in convenient wide mouth bottles. Calibrated to ± .005 gm/cc. Note: Much tighter tolerance than sets available elsewhere.

Application: For mineralogists and gemologists, Heavy Liquid sets are useful for quick, easy identifications, or classifying and separating specimens into groups.

For adjustments to temperatures, readings and/or coefficients – please see options at the bottom of this section.

Temperature Change from 23°C 

Cat #: 12610
Temperature Range: 18°C to 30°C
Added Charge:$164.00

Tolerance Change from ±0.005 g/cc to ±0.0005 g/cc

Cat #: 12609
Tolerance Specified: ±0.0005 g/cc
Added Charge: $126.50

NOTE: Formulated from organic liquids. Low end member is stable and nontoxic High end members are halogenated organic compounds. Miscible with most organic solvents.

CAUTION: Take normal precautions against contact and inhalation of halogenated organics.

(M)SDS
Data Sheet